deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations.

The 3Com Power over Ethernet Single-Port Midspan Solution can power an IEEE 802.3af compliant device, such as the 3Com Network Jack or IntelliJack Switch, over standard Category 5 or 5e Ethernet cabling. This 48-volt inline power source installs right in the switch closet, eliminating an exposed power supply and extra wiring at the workspace. Installing Power over Ethernet helps save time and money because it's less vulnerable to damage or tampering than a local power supply.

The Linksys 12 Volt Power Over Ethernet Adapter Kit lets you put your access points almost anywhere, by removing the requirement of nearby power outlets. By using the existing Category 5 Ethernet cabling to deliver power to many standard 12 volt access points and other network devices, you save the time, hassle, and expense of running AC power to the access point's installation location. The 12 Volt Power Over Ethernet Adapter Kit is a two piece set. The "Injector" sends both power and data over one Category 5 cable to your access point, wireless router or bridge. Then the tiny "Splitter", placed at the remote location, separates the network data and DC power back into two cables, and delivers them to the access point. The Injector can also be used by itself with POE-enabled network devices that accept 48 volts directly on a POE port.

The Cisco Unified IP Phone Power Injector is a midspan power injector designed and tested for use with Cisco Unified IP phones. The Cisco Unified IP Phone Power Injector sits between a switch port and the Cisco Unified IP phone, providing inline power capability to an unpowered switch port. It supports Cisco midspan power, IEEE 802.3af modes for supplying power to the attached phone, and 10/100/1000BASE-T Ethernet connections.

Cisco Aironet Power Injector provides Ethernet inline powering as an alternative to local power or inline power capable switches, while also providing improved device and cable organization.

The Power Injector LR2 converts the standard 10/100 BaseT Ethernet category 5 RJ-45 interface that is suitable for weather-protected areas to a dual F-Type connector interface for dual coaxial cables that are more suitable for harsh outdoor environments. While providing a 100baseT interface to the Cisco Aironet 1300 Series, the Power Injector LR2 also provides power to the unit over the same cables with a power discovery feature that protects other appliances from damage should they accidentally be connected. To support longer cable runs from your infrastructure network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable, enabling total cable runs up to 200 meters. Lightning and surge protection is also included at the F-Type connector interface to provide added protection to your network infrastructure devices. The LR2 Power injector requires a Cisco supplied 48V DC source.

D-Link, an industry leader in networking, introduces the DWL-P200 Power over Ethernet (PoE) Adapter. The DWL-P200 delivers both data and electrical power to Ethernet-enabled devices using a single Ethernet cable. Using Power over Ethernet, you eliminate the need to place an Ethernet-enabled device, such as a wireless access point, near a power outlet, giving you more freedom in placement.

D-Link, an industry leader in networking, introduces the DWL-P50 Power over Ethernet (PoE) Splitter. By using the DWL-P50, both data and electrical power can be delivered to a non-PoE Ethernet-enabled device from a single CAT5 Ethernet cable.

TRENDnet's TPE-101I power over ethernet Injector provides an innovative and cost effective solution to a variety of ethernet devices such as VoIP phones or wireless access points. Reduce costs by using existing CAT5 cable to deliver both power and data where power source is difficult to obtain.

CP Technologies POS-1000 Power over Ethernet Splitter

The Linksys POES5 Power Over Ethernet Splitter lets you put your Linksys IP Phones almost anywhere, by removing the requirement of nearby power outlets. The POES5 sends power and VoIP over one Category 5 cable to your Linksys IP Phone. When it's time to add or relocate a phone, the POES5 can simplify your installation. The POES5 provides an 802.3af PoE port for connection back to a PoE switch. The compact POES5 connects to the standard DC power input and RJ45 Ethernet port on the Linksys IP Phone (or other supported Linksys VoIP product) via two split cables. The POES5 can be then tucked away and concealed in the stand attached to the Linksys IP phone. Simplify your installation and place your Linksys IP Phones, or any of the other supported Linksys VoIP products in a preferred spot with the Linksys 5 Volt Power Over Ethernet (POES5) Splitter.

CP Technologies POI-2000 Power over Ethernet Injector

Cisco Power over Ethernet Power Injector LR

Cisco Power over Ethernet Injector

This Single AF Port Power over Ethernet Injector provides the benefits of Power-over-Ethernet for individual Motorola access ports. Once the power injector is connected to your Ethernet switch, power and data are then transmitted to the access port via the Ethernet cable. The power injector supplies effective independent overload and short circuit protection per port. With the power injector, you can use your current LAN infrastructure to supply power directly to your access ports from a central location, delivering a cost-effective power solution for your small-site deployment.